• 38 AWG ribbon coax cables
• Q Series®, Q2™ and B Series connectors
• 50 ohm and 75 ohm signal routing
• Vertical and edge mount termination to cable
• Captive panel screws and screw downs available
• Ideal for longer cable assemblies (6” to 40”)
  • .5mm, QTH/QSH connectors - HQCD
  • .5mm, BTH/BSH connectors - HBCD
  • .635mm, QTS/QSS connectors - SQCD
  • .635mm, MIT/MIS connectors - MICD
  • .635mm, QMS/QFS connectors - 6QCD
  • .8mm, QTE/QSE connectors - EQCD
  • .8mm, 75 ohm, QTE/QSE connectors - EQSD

• 34 AWG EyeSpeed™ Micro Coax
• Optimizes Signal Integrity with no transition boards between cable and contacts
• 50 ohm signal routing
• Rugged friction lock
• Hot swappable
  • .8mm (.315") - ERCDA

• 36 AWG EyeSpeed™ coax cable
• Optimizes Signal Integrity with no transition boards between cable and contacts
• 50 ohm signal routing
• Increased insertion depth for rugged applications
• Standard guide post holes
  • .635mm (.025") - Q2DA

• 30 AWG ribbon twinax cable
• Q Series®, Q2™, and Edge Card Connectors
• 100 ohm Differential Pair signal routing
• Vertical and edge card terminal to cable
• Locking and latching options
• Shielded and unshielded versions
• Optional screw downs
• Low skew
  • Pair-to-pair – < 10 ps/ft
  • Within pair - <5 ps/ft
• Superior EMI Performance (FCC Class A)
  • .5mm, QTH/QSH connectors - HQDP
  • .635mm shielded, QMSS/QFSS connectors - 6QDPS
  • .635mm unshielded, QMS/QFS connectors - 6QDP
  • .8mm, QTE/QSE connectors - EQDP
  • .8mm edge card connectors - EEDP

• JTAG (IEEE 1149.1) compatible
• 38 AWG ribbon coax cable
• 50 ohm signal routing
• Header or socket termination
  • .100” (2,54mm) – HHSC
  • .050” (1,27mm) – FHSC
  • 2mm (.0787”) – THSC

• Up to 2 ½ times the performance of traditional IDC flat cable
• High quality Tiger IDC contacts
• Variety of board level interfaces
• Differential cable routing
  • .050” (1,27mm) Male connectors - FMTP
  • .050” (1,27mm) Female connectors - FFTP

• 30 AWG twinax cable
• Optimizes Signal Integrity with no transition boards between cable and contacts
• Surface mount or panel mount
• Socket or terminal end connector options
• 8 pairs per chicklet; 4 chicklets per bank
• Choice of 1 or 2 banks for 32 or 64 pairs
• Bank holders with Finger Actuated Locking Clips
• Combination guide pin/locking posts solders to PCB
  • DataBank™ Cable Assembly – GCCA
  • DataBank™ Board Interface - GCAM

• 26 AWG Quiet Power™ coax cable minimizes EMI aggression and coupling of high speed signals
• 38 AWG 50 ohm coax cable supports high speed single-ended signals
• Standard 26 quiet power lines and 52 high speed coax lines
• Rugged Q2™ features and benefits
• Low 20 ohm impedance for fast power switching

View our Transmission Line Solutions Guide.

Click here to read more about our Custom High Speed Cables.

Click here to read more about Test and Debug Cables.

Click here to Build a High Speed Cable Assembly.

Click here to use Samtec’s High Speed Cable Performance Calculator.

Click here to view Samtec’s High Speed Cable Bandwidth Selector Guides for either Single-Ended or Differential Pair assemblies.

Click here to view our Mated Cable Heights Chart for our data rate cable assemblies.

Samtec Final Inch® Test and Evaluation Boards can be used to test our EQCD Series and HQCD Series High Speed Cable Assemblies.

Click here to view Samtec’s Industry Standards and Platforms for our High Speed Connectors.

For other questions on Samtec’s High Speed Cable Assemblies, contact our HDR Group or complete our on-line HDR Support Form.

Click here to view and register for our on-going Signal Integrity E-mail Tips.